Trenchless Sewer Repair Methods in Denver
An independent, licensed plumbing contractor. Not affiliated with Denver Water or the City and County of Denver.
Trenchless sewer repair rebuilds or replaces a failing line through existing access points instead of a continuous open trench. Denver Sewer & Water runs pipe bursting, cured-in-place lining, pull-in-place lining, and sectional spot repair, and we tell you plainly when none of them fit.
- Camera inspection before any method is chosen.
- Pipe bursting, CIPP, pull-in-place, and spot repair in house.
- Access pits instead of a full-length trench.
- Honest answer when open cut is the better call.
Get Your Free Quote!
What Trenchless Sewer Repair Actually Means
Trenchless sewer repair is a family of methods that restore a sewer line from small access points rather than by digging along the full length of the pipe. The work happens inside the existing pipe path, so driveways, mature trees, patios, and finished landscaping usually stay intact.
There is no single trenchless method. Lining rebuilds the inside of a pipe that still holds its shape. Bursting destroys the old pipe and pulls a new one into the same corridor. Spot repair treats one defect. The condition of your line decides which of those is possible.
Trenchless is a means, not a goal. A method that is wrong for the pipe you have will cost more and last less than a properly executed trench.
(720) 935-6221Methods That Fall Under Trenchless
- Pipe bursting for full replacement without a full trench.
- CIPP cured-in-place lining for continuous structural relining.
- Pull-in-place lining for shorter defined runs.
- Sectional spot repair for one isolated defect.
- Pipe reaming to restore diameter before a liner is installed.
- Directional boring when a new line needs a new path.
How We Diagnose It
When Trenchless Is the Right Method
Trenchless is the right method when the line is continuous enough to host a liner or to guide a bursting head, when access points exist at both ends or can be created cheaply, and when the surface above the line is expensive or impossible to restore.
It is the wrong method when the pipe is collapsed, severely offset, or crushed flat, when grade is wrong and needs to be reset, or when the line has to be rerouted because the existing path is the problem.
We confirm this with a camera inspection and a locate, not with an estimate over the phone. A method quoted before anyone has seen inside the pipe is a guess.
Conditions That Rule Trenchless Out
- Full collapse with no continuous bore to follow.
- Severe offsets or separated joints that a head cannot pass.
- Bellied line where the real defect is grade, not pipe wall.
- Required reroute or new connection point.
- No usable access pit locations at either end.
- Surrounding utilities packed too tightly for a safe pull.
How a Trenchless Project Runs Start to Finish
- 1
Inspect and Locate
Camera inspection plus electronic locating gives pipe material, diameter, defect type, depth, and the exact line path.
- 2
Select the Method
The findings point to lining, bursting, spot repair, or excavation. We explain why and what the alternatives would cost.
- 3
Open Access and Prepare
Small access pits are dug at the entry and exit points, and the line is cleaned or reamed so the method has a clean host pipe.
- 4
Install and Verify
The liner or new pipe goes in, then a post-work camera pass confirms the finished line before pits are backfilled and the surface is restored.
Talk Through the Method Before Work Starts
Disruption, Timeline, and What Drives Cost
Most residential trenchless projects are a one to two day job on site, with the pipe out of service for part of a single day. Two access pits are typically a few feet across rather than a trench running the length of the yard.
Cost is driven by line length, depth, diameter, pipe material, the number of access pits required, how much cleaning or reaming the host pipe needs before work starts, whether the line runs under a street or an alley that needs permitting and traffic control, and how much surface restoration follows.
We do not publish flat prices for underground work because two lines at the same length can differ by thousands once depth and access are known. You get a scoped quote after the inspection.
- For the full side by side of trenchless against open cut excavation, across disruption, restoration cost, time on site, pipe condition required, and result, see the sewer repair method comparison table
- To compare CIPP lining, pipe bursting, sectional spot repair, and pipe reaming across when to use each and what disqualifies it, see the trenchless method matrix
Frequently Asked Questions
Related Methods and Services
Method Comparison and Cost Guide
Side by side comparison of every method, what drives cost, and what rules each out.
Explore Method Comparison and Cost GuidePipe Bursting
Full line replacement pulled through the old pipe path without a long trench.
Explore Pipe BurstingCIPP Cured-In-Place Lining
A resin liner cured inside the host pipe to form a new jointless pipe wall.
Explore CIPP Cured-In-Place LiningSectional Spot Repair
A short liner or replacement section targeting one isolated defect.
Explore Sectional Spot RepairFind Out Whether Your Line Is a Trenchless Candidate
Camera inspection first, method second. Call for a scoped quote based on what is actually in the ground.