Pull-In-Place Pipe Lining in Denver
An independent, licensed plumbing contractor. Not affiliated with Denver Water or the City and County of Denver.
Pull-in-place lining draws a resin-saturated liner into a defined length of pipe from an access point, then inflates and cures it against the host pipe. It suits shorter, well-defined runs where a full inversion setup is unnecessary.
- Liner pulled into position rather than inverted.
- Efficient on short, defined runs.
- Works from a cleanout or a small access pit.
- Same structural result as inversion lining on the right job.
Get Your Free Quote!
What Pull-In-Place Lining Is
A liner is saturated with resin, attached to a pull rope or cable already run through the pipe, and drawn into position from the far access point. A bladder inside the liner is then inflated to press it firmly against the host pipe while the resin cures.
The difference from inversion CIPP is how the liner arrives at its position. Inversion turns the liner inside out with air or water pressure as it travels. Pull-in-place moves it mechanically, then inflates it once it is where it needs to be.
That makes pull-in-place practical when you have good access at both ends, a defined run length, and a job that does not justify mobilizing a full inversion setup.
(720) 935-6221Where Pull-In-Place Fits Best
- Shorter laterals with a clear start and end point.
- Runs where both ends are accessible.
- Lines with damage across a defined length rather than one spot.
- Jobs where positioning accuracy matters.
- Repairs following a spot repair that did not solve enough of the line.
How We Diagnose It
When Pull-In-Place Is the Right Method
Pull-in-place is the right method when the damaged length is defined and reachable from both ends, when the host pipe is round and correctly graded, and when the run is short enough that pulling the liner into position is straightforward.
It is a good middle option between a sectional spot repair, which treats a single defect, and a full inversion liner, which treats an entire run. If the defects cover most of one segment but not the whole line, this is often the efficient answer.
It is the wrong method when there is no second access point, when the pull would drag the liner across debris or sharp offsets, or when the pipe has the same disqualifying conditions that rule out any lining: collapse, belly, or missing wall.
Conditions That Rule Pull-In-Place Out
- Only one accessible end of the run.
- Long runs where pulling friction becomes a problem.
- Offsets or protrusions that would snag or damage the liner.
- Bellies and grade problems, which lining never corrects.
- Collapsed sections with no continuous bore.
- Host pipe not cleaned back to bare wall.
How a Pull-In-Place Liner Goes In
- 1
Inspect and Define the Run
Camera inspection sets the exact start and end of the damage and confirms both access points are usable.
- 2
Clean the Host Pipe
Jetting and cutting remove roots, scale, and grease so the liner bonds to pipe wall rather than debris.
- 3
Saturate and Pull Into Position
The liner is wet out, attached to the pull line, drawn into the run, and positioned precisely across the damaged length.
- 4
Inflate, Cure, Verify
The bladder inflates the liner against the pipe, the resin cures, the bladder is removed, and a camera pass documents the result.
Talk Through the Method Before Work Starts
Disruption, Timeline, and Cost Drivers
Most pull-in-place installations are a single day on site with the line out of service for a few hours. Excavation is usually limited to creating or exposing an access point.
Cost drivers are the length being lined, pipe diameter, cleaning and reaming needed beforehand, whether an access pit or new cleanout is required, cure method, and the number of service connections in the lined length.
On short runs this is frequently cheaper than mobilizing an inversion setup. On long runs the economics flip and inversion lining is the better value.
Frequently Asked Questions
Related Methods and Services
CIPP Cured-In-Place Lining
A resin liner cured inside the host pipe to form a new jointless pipe wall.
Explore CIPP Cured-In-Place LiningSectional Spot Repair
A short liner or replacement section targeting one isolated defect.
Explore Sectional Spot RepairTrenchless Sewer Repair
The umbrella page covering every no-dig and low-dig repair method we run.
Explore Trenchless Sewer RepairMethod Comparison and Cost Guide
Side by side comparison of every method, what drives cost, and what rules each out.
Explore Method Comparison and Cost GuideGet the Right Liner for the Length You Actually Need
We line the segment the camera says is failing, not more and not less.