# CIPP Cured-In-Place Pipe Lining in Denver

CIPP lining installs a resin-saturated liner inside your existing sewer line and cures it in place, forming a new jointless pipe within the old one. No trench, no new pipe path, and no joints for roots to find.

- Jointless structural pipe formed inside the old line.
- Installed through a cleanout or a single access point.
- Seals cracks, root intrusion, and leaking joints in one pass.
- Requires a host pipe still holding its shape.

## What Cured-In-Place Lining Is

A flexible felt or fiberglass liner is saturated with a two part resin, then inverted or pulled into the host pipe and inflated against the pipe wall. Heat, ambient temperature, or ultraviolet light cures the resin until it hardens into a rigid pipe that takes the shape of the original line.

Once cured, the liner is a structural pipe in its own right. It bridges cracks, seals open joints, blocks root entry points, and provides a smooth interior that improves flow even though internal diameter drops slightly.

Service connections are reinstated with a cutter after the cure, which is why lining is used on both residential laterals and larger commercial and municipal runs.

- Longitudinal and circumferential cracking.
- Root intrusion at joints.
- Leaking or open joints allowing infiltration.
- Corroded cast iron with a sound remaining wall.
- Interior scaling and roughness restricting flow.
- Minor deformation the liner can bridge.

## When CIPP Lining Is the Right Method

CIPP is the right method when the host pipe is structurally continuous, holds close to round, and has correct grade. The liner follows the shape it is given, so it preserves the geometry of the line rather than correcting it.

It is a strong choice for long runs under driveways, foundations, streets, and mature trees, and for lines with many joint defects, because one liner treats the whole run rather than repairing each defect individually.

It is the wrong method when the pipe is collapsed, has a belly, has severe offsets that the liner would simply reproduce, or has lost so much wall that there is nothing to line against. Diameter loss also rules it out on lines already running at capacity.

- Collapsed or crushed sections.
- Bellies and back-pitch, which a liner preserves rather than fixes.
- Offsets larger than the liner can bridge.
- Missing pipe wall leaving nothing to line against.
- Lines already undersized where diameter loss matters.
- Heavy scale or roots not fully removed before installation.

## How a CIPP Installation Runs

1. **Inspect and Measure** Camera inspection confirms the host pipe is a lining candidate and establishes exact length, diameter, and the location of every service connection.
2. **Clean and Ream** Jetting, cutting, and reaming remove roots, grease, and scale. A liner installed over debris fails, so preparation is not optional.
3. **Saturate and Install** The liner is wet out with resin and inverted or pulled into place, then inflated tight against the host pipe wall.
4. **Cure, Reinstate, Verify** The resin is cured, service connections are cut back open, and a final camera pass documents the finished pipe before the line returns to service.

## Disruption, Timeline, and Cost Drivers

Most residential liners are installed and cured within a single day, with the line out of service for several hours during cleaning, installation, and cure. Excavation is often limited to nothing at all when an existing cleanout can be used.

Cost drivers are run length, pipe diameter, how much cleaning and reaming the host pipe needs, cure method, the number of service connections to reinstate, access difficulty, and whether a cleanout has to be installed to get a launch point.

Lining is usually the lowest cost trenchless option per foot on a long run, but only where the host pipe qualifies. Preparing an unqualified pipe until it accepts a liner is how a lining project turns expensive.

## Frequently asked questions

**When is CIPP lining the right method?**

When the host pipe is continuous, close to round, and correctly graded, and when the defects are cracks, root intrusion at joints, or corrosion rather than collapse or grade failure.

**What rules CIPP lining out?**

Collapse, bellies, severe offsets, missing pipe wall, or a line already too small to give up any internal diameter.

**Does lining reduce the pipe size?**

Slightly. The liner takes a small amount of internal diameter, though the smooth interior often means flow capacity is equal or better than the scaled pipe it replaced.

**Can lining fix a belly in the line?**

No. A liner follows the existing shape, so a bellied line stays bellied. Correcting grade requires excavation.

**How long does a cured liner last?**

A correctly prepared and installed liner is a long term structural repair rather than a patch. Preparation of the host pipe is the biggest factor in how it performs.

## Related Methods and Services

- [Trenchless Sewer Repair](https://www.denversewerandwater.com/methods/trenchless-sewer-repair) The umbrella page covering every no-dig and low-dig repair method we run.
- [Pull-In-Place Lining](https://www.denversewerandwater.com/methods/pull-in-place-lining) A liner pulled into position from one access point for shorter defined runs.
- [Pipe Reaming](https://www.denversewerandwater.com/methods/pipe-reaming) Cutting the interior of a pipe back to full diameter before lining or cleaning.
- [Method Comparison and Cost Guide](https://www.denversewerandwater.com/methods/sewer-repair-method-comparison) Side by side comparison of every method, what drives cost, and what rules each out.

---

Denver Sewer and Water is a privately owned, licensed and insured plumbing contractor. We are not affiliated with, endorsed by, or connected to Denver Water, the municipal water utility, or any government entity. To pay a municipal water bill or reach the public utility, visit denverwater.org.

Source: https://www.denversewerandwater.com/methods/cipp-lining